added german messages and put only servo motor in toolbox

2022-07-30 23:32:22 +02:00
parent de15bcf993
commit 047588842c
8 changed files with 172 additions and 100 deletions
@@ -0,0 +1,48 @@
+export const MOTORS = {
+
+    /**
+     * Motors
+     */
+
+    sensebox_motors_beginServoMotor: "Initialisiere Servomotor",
+    sensebox_motors_beginServoMotor_pin: "Pin:",
+    sensebox_motors_beginServoMotor_tooltip: "Verbinde einen digitalen Pin mit dem orangen Kabel des Servomotrors. Verbinde zusätzlich GND mit GND (schwarzes und braunes Kabel) und 5V mit 5V (rotes Kabel).",
+    sensebox_motors_beginServoMotor_helpurl: "https://de.wikipedia.org/wiki/Servomotor",
+
+    sensebox_motors_moveServoMotor: "Bewege Servomotor",
+    sensebox_motors_moveServoMotor_pin: "Pin:",
+    sensebox_motors_moveServoMotor_degrees: "Winkel in Grad:",
+    sensebox_motors_moveServoMotor_tooltip: "Der Servomotor kann zwischen 0 und 180 Grad bewegt werden.",
+    sensebox_motors_moveServoMotor_helpurl: "https://de.wikipedia.org/wiki/Servomotor",
+
+    sensebox_motors_I2CMotorBoard_begin: "Initialize I2C Motor Board",
+    sensebox_motors_I2CMotorBoard_begin_tooltip: "Connect the I2C Moztor Board with the two DC Motors to one of the five I2C-Ports. Use this Block inside the setup()-function.",
+    sensebox_motors_I2CMotorBoard_begin_helpurl: "TODO",
+
+    sensebox_motors_I2CMotorBoard_moveDCMotor: "Move",
+    sensebox_motors_I2CMotorBoard_moveDCMotor_left: "left",
+    sensebox_motors_I2CMotorBoard_moveDCMotor_right: "right",
+    sensebox_motors_I2CMotorBoard_moveDCMotor_motor: "DC Motor at I2C Motor Board",
+    sensebox_motors_I2CMotorBoard_moveDCMotor_speed: "Speed:",
+    sensebox_motors_I2CMotorBoard_moveDCMotor_tooltip: "You can set the Speed between -100 and 100.",
+    sensebox_motors_I2CMotorBoard_moveDCMotor_helpurl: "TODO",
+
+    sensebox_motors_I2CMotorBoard_stopDCMotor: "Stop ",
+    sensebox_motors_I2CMotorBoard_stopDCMotor_left: "left",
+    sensebox_motors_I2CMotorBoard_stopDCMotor_right: "right",
+    sensebox_motors_I2CMotorBoard_stopDCMotor_motor: "DC Motor at I2C Motor Board",
+    sensebox_motors_I2CMotorBoard_stopDCMotor_tooltip: "TODO",
+    sensebox_motors_I2CMotorBoard_stopDCMotor_helpurl: "TODO",
+
+    sensebox_motors_beginStepperMotor: "Initialize Stepper Motor (28BYJ-48)",
+    sensebox_motors_beginStepperMotor_rpm: "Rotations per Minute:",
+    sensebox_motors_beginStepperMotor_pins: "Input Pins (IN1-IN4):",
+    sensebox_motors_beginStepperMotor_tooltip: "Connect four of the the digital pins in the right order to the inputs IN1-IN4 on the stepper motor board. Connect a GND pin (black wire) to the minus pin and a 5V pin (red wire) to the plus pin on the board. Also connect the stepper motor to this Board. Use this Block inside the setup()-function.",
+    sensebox_motors_beginStepperMotor_helpurl: "TODO",
+
+    sensebox_motors_moveStepperMotor: "Move Stepper Motor (28BYJ-48)",
+    sensebox_motors_moveStepperMotor_step: "Steps:",
+    sensebox_motors_moveStepperMotor_tooltip: "Move stepper motor. 2048 steps equal a full rotation.",
+    sensebox_motors_moveStepperMotor_helpurl: "TODO",
+};
+